La Belle Alliance Part Five

Hello There! I have continued to progress with the Waterloo building. The previous part is here. Now, I can describe adding and weathering the roof on the extension, weathering the window and door frames and applying a rust finish to the bars on the windows and door hinges.

This is a picture of a roof on a building at a previous game at New Buckenham Historical Wargamers. At this point I had not decided what finish I wanted to aim for.

I reached a decision when I drove over to a wargames friends new house, after he had recently moved. I drove through a part of a VERY rural Suffolk. 

On the way I saw a pantile roof on an old building and it was covered in moss. I though that during the Napoleonic period people would not be bothered about removing this and moss would be a lot more prevalent than now considering the less polluted environment

To start off with I used some pantile roof sheets from the Wills Scenics range of plastic materials.

The above is the roof for the main building. The roof was self colour. However it did not take paint well. I wanted to add different shades of tiles to the roof. I glued two sheets together to make the correct size for one side of the building. Above is the original colour on the left, enamel white undercoat in the middle and the repainted, (Vallejo 929 Light Brown), on the right.

The newly painted sheet on the right also had a slightly grainy finish.

I added some slightly different shades to the individual roof tiles. Unfortunately this does not show up well on this photograph.

I then washed the roof in Army Painter Quick Shade Strong tone.

When dry, I added a wash of AK interactive Slimy Grime Dark mixed with Woodland Scenics fine turf. The colour of the turf does not matter as the AK interactive product will colour it.

I then added small portions of the mix to the troughs of the roof to represent moss clumps. After this has dried I washed the roof in a 50:50 mix of PVA and water to hold the moss on the roof.

The clumps were painted 872 Chocolate Brown. When dry the top surface was painted 922 Intermediate green.

Next I painted the woodwork on the windows, doors, window shutters and barge boards.

I copied the system for painting worn old timber from Emmanuel Nouaillier. In the June 2008 edition of Continental Modeller he used a mixture of Humbrol enamel paints. (Matt numbers 27, 28, 98, 119 and 147). Using enamels come with the usual odours, especially from white spirit, when used as a thinner, and in my case the resulting headache.

I thought that it would be possible to use Vallejo acrylics. I found equivalent colours in 859, Basalt Grey, 875, Beige Brown, 841, Burnt Umber and 992, Neutral Grey. Thinning with water worked just as well.

First you clean the plasticard. Add a wood grain to it by rubbing the face of the strips with a suede brush, or for a deeper grain a wire brush. I make the grain deeper by scoring it with a scalpel with a no. 11 blade. The previous fine grain from the brushing guides the scalpel point so it does not meander all over the card. Remove the swarf from the plasticard. Make the frame, or in the case above, the window shutters. Glue them together with 'liquid glue for plastic' by Revell. Allow to dry. If you do get finger prints on the scored plastic, do not worry. Leave it to dry and rescore later.

Paint the whole item in enamel white and allow to dry.

The idea of painting is to wash the colours over the plasticard card and merge the colours together. You can try to get different shade on individual planks. Do not worry about the planks being too light or dark. Try to leave a hint of the various colours from the Vallejo colours listed above.

After the wood effect has dried, I washed in a thin coat of 950 black.

As the doors were treated the same as above, the door hinges were painted in 981 Orange Brown. This is the base of the rust finish.

I masked the rest of the door off. 

Then added a coat of pigment fixer on the bear hinges and added a covering of AK dark rust AK2042.

Before adding a coat of more pigment fixer to the surface of the pigment, I gently brushed away the excess pigment. I then dropped a further layer of pigment fixer and allow to dry before adding more pigment fixer.

After removing the masking tape I ended up with this effect. Any excess pigment that found its way under the masking tape can be removed using white spirit on a paintbrush and washing it away. 

As you may see in the above photographs I have added 'glass' to the windows. I used 'Leaded Windows, Diamond Pattern' from Scale Model Scenery. Another supplier to the model train world which can be very helpful.

Last I have added the 'La Belle Alliance' sign. This is made from foamcore. After cutting to size I  covered it in a layer of AK Terrains Dry Ground, AK8015. I let that set, and painted 820 off white. I used a 3mm high engineering, metal stamp set, to make the impression of the letters, and then filled in the impressions with 0.3mm tip pigment liner.

Next I shall add the timber boards to each end of the building and the main roof.

Battle of Caldiero 1796

Hello There! Recently the New Buckenham Historical Wargamers put on an early Napoleonic wargame along the lines of the Battle of Caldiero, 1795.

Here is an overall view of the battlefield. It was fought using 28mm figures and used figures from a few collections from various club members. The rules used were Shako 2 with some club modifications. Prussian figures stood in for the Austrians.

As you can see the quality of figure painting was high.

The French came on to take the settlements in front of the ridge which the Russian forces occupied.

Here is one of the attacks on a village.

And another view of the same attack.

The Russian figures used reflected the later 1812 uniforms as we do not have figures available for the earlier period. 

Here French chasseurs  try to clear enemy cavalry from the hill so their infantry can take the hill. The changeable weather stopped many charges from taking place as it stopped infantry firing, if they were not in a village and cavalry could not charge.

A highly enjoyable game and very good company.

Further photos of the game are here.

Military Prints

Hello There! I have been trying to build up some decorations for the wargaming cabin, and attempting to keep the the costs down.

After searching Facebook market place I found a number of very cheap picture frames. At the same time I also searched through a few charity shops for further suitable frames.

Here is a print that I found in a second hand book shop in York. As I was painting some French Light Infantry at the time. It is entitled 'Infanterie Legere 1809 - voltigeur - carabinier'

All the bare wood frames have been stripped and painted in  dark green to blend in the fittings in the cabin which are the same colour. This print and the next came from Bastion Books in Berwick on Tweed.

It is entitled 'A corporal of 13th light dragoons killing a French colonel Campo Mayor, Spain 1811'

This last print was an illustration of the Royal Norfolk Regiment advancing at the Battle of Roleia. Entitled 'Ninth Regiment of Foot Battle of Roleia 17th August 1808'

Being the local regiment I felt it was a good portend.

La Belle Alliance Build Part Two

Hello There! I have made some more progress on the build. The start of the build is here.  After starting to cut out the spaces for the doors and windows I found that the width of the gaps for the doorframes and window frames were too small for the front of the building.

Using the grid on the graph paper I was able to widen them both a standard size. I use a sharp scalpel to cut the openings.

During this I made one cut which while it was 'clean' it was not square so the subsequent door and frame would not have sat correctly. In the picture below the left hand cut on the door is misaligned. You can see the mixed Miliputt on the right to correct this.

Here I have put the miliputt in place and fitted the door frame. I waited for this to set and then glued both in place with gel superglue.

I used an engineers square to get both in the right position.

Concerning the timber for the doors and windows, I used a suede brush and then a wire brush to impress a wood grain into the plastistrut. To make this deeper and more pronounced I then ran the tip of a pointed scalpel along as well. This also gave you less chance of running of the side off the plastistrut as the existing small grooves from the wire brushes provided a guide. 

The grooves along the outside edge of the door frame were made using a pointed scalpel again with the plastistrut placed flat on a cutting board and then run along the edge.

The windows are in two parts. The top part is leaded and the lower part is guarded with iron bars which are held in place by horizontal beams against the transom of the frame. I cut the upper and lower parts of the horizontal beams that the bars will fit into. I cut them the same length and held them together while I drilled holes through them so the vertical bars would be vertical. (I had to do this twice so they were parallel!).

With the window bars fitted I started on the doors. These were also made from plasticard and a wood grain finish was added as before. the uprights were added to two parallel beaks, as seen above.

I then peeled off the surface card on the foam.

With all the doors and windows fitted I began to emboss the bricks onto the surface. This was done with the shaped ferrule of an old paint brush . A six inch steel rule was used to maintain a straight line for the bricks.

In the next part I hope to start the priming and painting.

La Belle Alliance Build Part One

Hello there! I have started revamping some buildings associated with The Battle of Waterloo. I have begun with Napoleons headquarters so that I can judge how best to do this work so that I can progress with the other buildings, Hougoumont and La Haie Sainte. 

I started off with this. I started by stripping the doors and windows and removing the roof and end extension.

This gave me the bare bones of the foam board shell. Here I have added some depth to each end as I had completed the next step below.

I searched the internet for reference material. I found that some representations of this building had made a number of mistakes as there was a few differences to what the building looked like during the battle and after a number of changes had been made.

The sepia illustration above was the most accurate I could find which was contemporary with the battle. I was completed a few months after the battle.

The black and white picture is from Adkins 'The Waterloo Companion' That shows some smaller windows under the eaves which were a later addition. Lastly on the front facing the road the left hand doorway was bricked up. In most models it is a door.

There does not appear to be any detailed pictures of the rear of the building. There is a well and a separate building behind but this is not included in this work.

I obtained some graph paper and started a scale drawing with the reference information I had. I also needed to take into account the dimensions of the foam board model I had to work with and the spacing of the doors and windows to make them look right.

Once that was done I then photocopied the plans and glued them to a sheet of Canson Foamboard. This is a much higher quality foam board than what is available from the likes of Hobbycraft. It is denser and is sandwiched with two sheets of cartridge paper. It is much easier to peel of and leaved a clean area which can be impressed with brick much more easily.

The wider dimensions, between the above plan and the foamcore shell was different. The plan being much wider. I added some further width by cutting some cheaper foamcore board a little smaller than what was already there and glued them to each end. The final ends where cut in Canson foamboard so I could impress a brick end to it later.

This also gave me the final width for the front and back and ensured that it would all fit together with no overlapping.

As you can see above I have started to cut out the doors and windows. This gave me the opportunity top enlarge them, to suit 28mm figures more easily and take into account the thickness of the plasticard which will be the door surrounds.

Next I will fit the doors and windows

Round up of book purchases

Hello there! I have found a few photographs lurking on my camera again. In an effort to clear the camera memory before going abroad later in the year, I have posted them on here.

The first two publications came from E Bay. I have been looking at Sherman tank design and the noticable difference between different marks. I have some 20mm 3D prints to paint. I have removed many of the print lines but the rear engine deck is incorrect and I am considering adding an engine access door(s).

The next, also from e Bay complements the other two Nafziger publications on the infantry and SS units.

These came from a couple of secondhand bookshops in Edinburgh, (below). There are many such places in the city and all well worth a visit.

Visit to Hay on Wye

 Hello there! While taking the opportunity to try out the mobile home again, we passed through the second hand bookshop capital of the United Kingdom.

Hay on Wye is a great place to visit if you would like to expand your library.

I was drawn to these as they are packed with photographs of the American Civil War. I used similar sources of illustrations to make some officers and other ranks tents a few years ago. In particular these have photographs of numerous wagons and carts used by both armies and also journalists developing wagons. All potential projects for the future.

This was an addition to my Almark collection. It is very generic and broad in its remit but was in good condition for its age.

Although I have a collection of  Concord publications, I do not usually collect much material on the SS or even the conflict in Russia. I saw these, which were a vey good price. Again in very good condition and matched with a couple of future projects for North West Europe.

Battle of Quatre Bras 16 June 1815

Hello there! I have started to catch up on some of the games I have attended at the New Buckenham Historical wargames Club.

The original buildings at Quatre Bras, are now sadly demolished. I visited the site in 2016 and the area was boarded off but I managed to get some photos of the buildings before they were lost.

These are 3D printed buildings.

There were plenty of extra figures on the table.

The Waterloo Panorama has these figures on it. These are Perry Sculpts.

This was a very enjoyable game with many club members in attendance.

There are further pictures on the New Buckenham Historical wargamers Facebook page here.